HOW TO REPAIR YOUR PHONES THAT FALLS INTO THE WATER

• REMOVE IT TO PIECES 

After you have removed the battery, dry off the cell phone with an absorbent towel as best as you can. Use cotton swabs to soak up water in crevices and on any fragile, exposed circuits. If you have dropped your cell phone in water, it also is helpful to disassemble it, if you can, and let all of the parts dry separately. Just be sure that you know how to put it back together. If it is a flip or sliding cell phone, leave it open to allow for maximum dryness

• AVOID MINERALS DAMAGES

If you drop your cell phone in water that isn't pure or another liquid, such as a beverage or in salt water, rinse off the phone with fresh water after you have removed the battery. After you drop your cell phone in water, a quick rinsing is unlikely to do any further damage, but salt, sugar or other materials might. You also could try giving your phone an alcohol bath. The alcohol will displace minerals and microscopic substances and will aid in the evaporation of the fluid. If it is available, you should use an alcohol concentration of 95 percent rather than rubbing alcohol, which usually has a concentration of 70 percent.

• BE PATIENT LET IT DRY THOROUGHLY

After your phone is clean, leave it in a warm, dry area or near an air conditioner for at least three days before you attempt to replace the battery and turn it on. This is very important, because although you may think that you have thoroughly dried it, the slightest moisture can react with the battery and cause it to short circuit. Putting your cell phone in a container full of dry rice grains also can help dry it out. Make sure that the rice completely covers the phone. 

    

• WARRANTY LIKELY VOIDED

 Unless you have insurance for your cell phone and it covers water damage, there probably is no point in sending it to the manufacturer with the hope that the warranty will cover the cost of a replacement. If you drop your cell phone in water, the warranty probably will be voided. The manufacturer's technicians will be able to tell immediately that it has been dropped in water because of the moisture-sensitive stickers that are placed inside almost all cell phones. The best thing to do is to dry it out yourself and hope that it still works

 

                 latunji benedict

est the Phone

• After the phone has dried thoroughly, replace the battery and turn on the phone. If the phone still doesn't work, it could be that the battery was damaged. You might want to try a replacement battery before replacing the entire phone. You could also have the phone looked at by a professional, depending on what is most cost-effective for you.
  

Warnings

• Excessive heat may damage a cell phone; never use hair dryers, heat lamps, microwave or conventional ovens or direct sunlight to dry a wet cell phone.
  If a cell phone has been submerged in salt water, rinse with fresh water after removing the battery and before the drying process to remove as much salt as possible.
  

Keeping Your Phone Dry

• Following are some of the most common water hazards for cell phones and ways to avoid them.
  - Toilet: If you are in the bathroom be sure your phone is secure, particularly if you tend to carry it in your pants pocket.
  - Washing machine: Check all pockets thoroughly before doing laundry.
  - Bathtub: It is best not to use your cell phone while in the bathtub.
  - Kitchen sink: Keep cell phone free and clear of kitchen sink while doing dishes.
  - Rain: Make sure cell phone is secure in a pocket or purse before going out into the rain. Do not use cell phone during a heavy rain unless you are under shelter

Read more : http://www.ehow.com/about_5097400_cell-phone-falls-water.html

est the Phone

• After the phone has dried thoroughly, replace the battery and turn on the phone. If the phone still doesn't work, it could be that the battery was damaged. You might want to try a replacement battery before replacing the entire phone. You could also have the phone looked at by a professional, depending on what is most cost-effective for you.
  

Warnings

• Excessive heat may damage a cell phone; never use hair dryers, heat lamps, microwave or conventional ovens or direct sunlight to dry a wet cell phone.
  If a cell phone has been submerged in salt water, rinse with fresh water after removing the battery and before the drying process to remove as much salt as possible.
  

Keeping Your Phone Dry

• Following are some of the most common water hazards for cell phones and ways to avoid them.
  - Toilet: If you are in the bathroom be sure your phone is secure, particularly if you tend to carry it in your pants pocket.
  - Washing machine: Check all pockets thoroughly before doing laundry.
  - Bathtub: It is best not to use your cell phone while in the bathtub.
  - Kitchen sink: Keep cell phone free and clear of kitchen sink while doing dishes.
  - Rain: Make sure cell phone is secure in a pocket or purse before going out into the rain. Do not use cell phone during a heavy rain unless you are under shelter

Read more : http://www.ehow.com/about_5097400_cell-phone-falls-water.html

Disconnect Power Immediately

• The first and most critical step is to remove your wet cell phone's battery and SIM card as soon as possible. Do not attempt to power up the phone to see if it works, as this can damage the circuits. Set the battery aside and save the SIM card in order to retain critical information in case you need to get a new phone after all.
  

Dry Thoroughly and Quickly

• The cell phone should be dried as quickly and thoroughly as possible to avoid water damage. Compressed air or a wet/dry vacuum are ideal for removing water. Avoid any type of heat, such as a blow dryer, heat lamp or direct sunlight, which can warp or melt delicate electronic components and connectors. After removing as much water as possible, submerge the phone in a desiccant, such as dry rice, to remove any remaining traces of water. Silica gel packets are another desiccant option. Leave overnight.

Read more : http://www.ehow.com/about_5097400_cell-phone-falls-water.html

Disconnect Power Immediately

• The first and most critical step is to remove your wet cell phone's battery and SIM card as soon as possible. Do not attempt to power up the phone to see if it works, as this can damage the circuits. Set the battery aside and save the SIM card in order to retain critical information in case you need to get a new phone after all.
  

Dry Thoroughly and Quickly

• The cell phone should be dried as quickly and thoroughly as possible to avoid water damage. Compressed air or a wet/dry vacuum are ideal for removing water. Avoid any type of heat, such as a blow dryer, heat lamp or direct sunlight, which can warp or melt delicate electronic components and connectors. After removing as much water as possible, submerge the phone in a desiccant, such as dry rice, to remove any remaining traces of water. Silica gel packets are another desiccant option. Leave overnight.

Read more : http://www.ehow.com/about_5097400_cell-phone-falls-water.html

Disconnect Power Immediately

• The first and most critical step is to remove your wet cell phone's battery and SIM card as soon as possible. Do not attempt to power up the phone to see if it works, as this can damage the circuits. Set the battery aside and save the SIM card in order to retain critical information in case you need to get a new phone after all.
  

Dry Thoroughly and Quickly

• The cell phone should be dried as quickly and thoroughly as possible to avoid water damage. Compressed air or a wet/dry vacuum are ideal for removing water. Avoid any type of heat, such as a blow dryer, heat lamp or direct sunlight, which can warp or melt delicate electronic components and connectors. After removing as much water as possible, submerge the phone in a desiccant, such as dry rice, to remove any remaining traces of water. Silica gel packets are another desiccant option. Leave overnight.

Read more : http://www.ehow.com/about_5097400_cell-phone-falls-water.html

Learn and Create Bead Making

BEAD MAKING

Bead Making

BEAD making is a very good act of keeping yourself busy, and also making a hell of income. There are so many ways of making beads

Beginner's jewelry making instructions in how to choose your first project.

For a Beginner, one of the most intimidating steps in jewelry making is to actually begin making a jewelry item.  The obvious first question is what do a beginner need to know to begin.  In the following paragraphs we will try to show where to go to learn the basic skills that are necessary in working with wire and beads and will identify some resources to visit to learn how to perform these skills.
Perhaps even more important than showing you where to go to learn the skills, we will actually suggest your first jewelry project. The reason we make this suggestion for a first project is that we have talked to too many people who found a jewelry project that they wanted to make and commenced by trying to make that project without understanding whether the project was suitable for a beginner or not.
 

lovely Bead Making

  Infinity Jewelry Wire & Beads Earrings
Select the picture or text
above to link to our instructions
for making these earrings.      Queen of Clubs Earrings    
Select the picture or text
above to link to our instructions
for making these earrings.  



Now let's try to answer the obvious question -- What makes a project suitable for a beginner? 

1. Instructions are detailed explaining every step in the process.
2. Where skills are required, the instructions include a link to a description of how to perform that skill.
3. Where appropriate videos are referenced to help understand the techniques used. 
4. Instructions include a picture for every step in the project. 
5. In general, we assume that any project that requires wrapping wire around itself, is not suitable for beginners. 

Before we actually recommend a jewelry making project for beginners, let's discuss how we organize our free jewelry making instructions.  For every jewelry making project that we describe on our web site we start with several introductory paragraphs like these.  The introductory paragraphs include some general discussion like this paragraph, a picture of the finished jewelry item like the picture above-right, and three sections that list the Supplies, Tools and Skills necessary to complete that project.  After these three paragraphs, we begin our step-by-step instructions for making that jewelry item.  The Supplies, Tools and Skills paragraphs below are those associated with our recommended beginners first jewelry project. 
The first jewelry projects that we recommend for beginners is our Infinity Jewelry Wire & Beads Earrings and our Queen of Clubs Earrings projects shown above.  At the bottom of this web page we will provide a link to our instructions for making these earrings. 

Jewelry Making Supplies: 6 inches of 20 Gauge inexpensive practice wire Two six mm beads Two three mm beads Ear wire findings (one pair)

Jewelry Making Tools: Ruler Flush Cutter Round Nose Pliers Bent Chain Nose Pliers (2) Any WigJig acrylic jig 20 minutes of free time

 

Jewelry Making Skills:

• How to use a flush cutter to cut wire.
   
• How to straighten wire using nylon jaw pliers. 
   
• How to grasp wire and bend wires using chain nose or bent chain nose pliers.
   
• How to make an open loop.
   
• How to use a WigJig to make jewelry wire components.

Step 1:  Before making any jewelry item,

Step 2:  Assemble the supplies and tools required. 
Step 3:  Review the instructions for the jewelry making skills required. 
Step 4:  When you have completed all of the above you are ready to make the earrings.  We use these projects for our recommended first project because these earrings are easy and quick to make.  This helps to ensure that your first jewelry making project will be successful.  
For more info contact: 08182374418
                            LATUNJI BENEDICT

BEAD MAKING

Bead Making

BEAD making is a very good act of keeping yourself busy, and also making a hell of income. There are so many ways of making beads

Beginner's jewelry making instructions in how to choose your first project.

For a Beginner, one of the most intimidating steps in jewelry making is to actually begin making a jewelry item.  The obvious first question is what do a beginner need to know to begin.  In the following paragraphs we will try to show where to go to learn the basic skills that are necessary in working with wire and beads and will identify some resources to visit to learn how to perform these skills.
Perhaps even more important than showing you where to go to learn the skills, we will actually suggest your first jewelry project. The reason we make this suggestion for a first project is that we have talked to too many people who found a jewelry project that they wanted to make and commenced by trying to make that project without understanding whether the project was suitable for a beginner or not.
 

lovely Bead Making

  Infinity Jewelry Wire & Beads Earrings
Select the picture or text
above to link to our instructions
for making these earrings.      Queen of Clubs Earrings    
Select the picture or text
above to link to our instructions
for making these earrings.  



Now let's try to answer the obvious question -- What makes a project suitable for a beginner? 

1. Instructions are detailed explaining every step in the process.
2. Where skills are required, the instructions include a link to a description of how to perform that skill.
3. Where appropriate videos are referenced to help understand the techniques used. 
4. Instructions include a picture for every step in the project. 
5. In general, we assume that any project that requires wrapping wire around itself, is not suitable for beginners. 

Before we actually recommend a jewelry making project for beginners, let's discuss how we organize our free jewelry making instructions.  For every jewelry making project that we describe on our web site we start with several introductory paragraphs like these.  The introductory paragraphs include some general discussion like this paragraph, a picture of the finished jewelry item like the picture above-right, and three sections that list the Supplies, Tools and Skills necessary to complete that project.  After these three paragraphs, we begin our step-by-step instructions for making that jewelry item.  The Supplies, Tools and Skills paragraphs below are those associated with our recommended beginners first jewelry project. 
The first jewelry projects that we recommend for beginners is our Infinity Jewelry Wire & Beads Earrings and our Queen of Clubs Earrings projects shown above.  At the bottom of this web page we will provide a link to our instructions for making these earrings. 

Jewelry Making Supplies: 6 inches of 20 Gauge inexpensive practice wire Two six mm beads Two three mm beads Ear wire findings (one pair)

Jewelry Making Tools: Ruler Flush Cutter Round Nose Pliers Bent Chain Nose Pliers (2) Any WigJig acrylic jig 20 minutes of free time

 

Jewelry Making Skills:

• How to use a flush cutter to cut wire.
   
• How to straighten wire using nylon jaw pliers. 
   
• How to grasp wire and bend wires using chain nose or bent chain nose pliers.
   
• How to make an open loop.
   
• How to use a WigJig to make jewelry wire components.

Step 1:  Before making any jewelry item,

Step 2:  Assemble the supplies and tools required. 
Step 3:  Review the instructions for the jewelry making skills required. 
Step 4:  When you have completed all of the above you are ready to make the earrings.  We use these projects for our recommended first project because these earrings are easy and quick to make.  This helps to ensure that your first jewelry making project will be successful.  
For more info contact: 08182374418
                            LATUNJI BENEDICT

GOVERNOR RAUF AREGBESOLA

IT 5 days from the Electoral pull of the Osun State, and the people of Osun has made their choice that the icon Governor Rauf Aregbesola is the man of their dreams. Congratulations to the Governor, we wish you happy governing. But, some of his competitors are not to happy about it and believe it was a wrong election,when even the people of Osu has concluded that the Independent National Electoral Commission (INEC) has done a very successful job. Iyiola Omisore belives their was a manipulation in the Election. But Is it the Governorship that matters or the betterment of the people?  According to me, every one is a governor. You dont wait for the Governor to feed you,definitely you do that yourself,So why wait for the Governor to do all most every thing,when you know you could per take in some,if not all. So people of  Nigeria let be our own Governor and make the best of every situation that can improve our beloved Country. It could be in different forms,some plan it as NGOs and many more. We could do this if we are together. God bless Nigeria                                                      

NIGERIA 

The worst and deadly disease of Mankind

This virus is so far the most deadly virus on planet earth. Killing at least 700 people in West Africa,with its pride of unforgivable mercy stinging Humans alive. But first what is EBOLA?
Ebola virus disease (EVD) or Ebola hemorrhagic fever (EHF) is the human disease caused by the Ebola virus. Symptoms typically start two days to three weeks after contracting the virus, with a fever, sore throat, muscle pain and headaches. Typically nausea, vomiting, and diarrhea follow, along with decreased functioning of the liver and kidneys. At this point, some people begin to have bleeding problems.The virus may be acquired upon contact with blood or bodily fluids of an infected animal (commonly monkeys or fruit Bat).Spread through the air has not been documented in the natural environment. Fruit bats are believed to carry and spread the virus without being affected. Once human infection occurs, the disease may spread between people as well. Male survivors may be able to transmit the disease via semen for nearly two months. In order to make the diagnosis, typically other diseases with similar symptoms such as malaria, cholera and other viral hemorrhagic fevers are first excluded. To confirm the diagnosis blood samples are tested for viral antibodies, viral RNA, or the virus itself.Prevention includes decreasing the spread of disease from infected monkeys and pigs to humans. This may be done by checking such animals for infection and killing and properly disposing of the bodies if the disease is discovered. Properly cooking meat and wearing protective clothing when handling meat may also be helpful, as are wearing protective clothing and washing hand with anti septic when around a person with the disease. Samples of bodily fluids and tissues from people with the disease should be handled with special caution.There is no specific treatment for the disease; efforts to help persons who are infected include giving either oral rehydration therapy (slightly sweet and salty water to drink) or intravenous fluids.The disease has high mortality rate: often killing between 50% and 90% of those infected with the virus.^[1][3] EVD was first identified in Sudan and the Democratic Republic of the Congo. The disease typically occurs in outbreaks in tropical regions of Sub-Saharan Africa.^[1] From 1976 (when it was first identified) through 2013, fewer than 1,000 people per year have been infected.^[1][4] The largest outbreak to date is the ongoing 2014 West Africa Ebola outbreak, which is affecting Guinea, Sierra Leone, Liberia and Nigeria.^[5][6] As of August 2014 more than 1750 suspected cases have been reported. Efforts are ongoing to develop a vaccine; however, none yet exists.                                                                                                                          Latunji benedict